home *** CD-ROM | disk | FTP | other *** search
-
- ====>>>> Key Commands available in Instrument Panel Screen <<<<===== 1
-
- Keys followed by + or - will allow you to repeatedly press
- + or - for the same effect until you press another key.
-
- Ctl-A Toggle Autopilot between NAVLOCK and HEADING modes.
-
- Ctl-M Go to Map Mode
-
- Enter Reset Time Compression to 1x
-
- Ctl-N cycle Day/Dusk/Night
-
- Esc abort current function, back out of menu,
- show main menu if none visible.
-
- Space Toggle Brakes on/off
-
- ' Change Fuel Selector
-
- / Toggle Brakes on/off
-
- 1-9 Menu Options
-
- A Toggle Autopilot On/Off
-
- F+ Extend Flaps 1 notch
- F- Retract Flaps 1 notch
-
- G Toggle Gear
-
- H+ Increase Carb Heat
- H- Decrease Carb Heat
-
- K Calibrate Joystick
-
- M+ Lean Mixture
- M- Rich Mixture
-
- P Toggle Pause
-
- S Toggle Engine Sound
-
- T Cycle Stop Watch Timer (Stop, Reset, Start)
-
- [ Close Cowl Flaps
- ] Open Cowl Flaps
-
- <> (But UNshifted, so comma and period) Move AutoPilot Bug.
-
- ` Toggle Menu
-
-
- 2
-
- Alt-A Next Autopilot Altitude Hold mode (OFF/ALT/ILSLOCK)
- Alt-B Toggle Beacon (Strobe)
- Alt-D Move Autopilot Bug
- Alt-F Toggle Fuel Pump
- Alt-G+/- Increase/Decrease Directional Gyro setting
- Alt-K+/- Increase/Decrease Altimeter Setting (Kollsman window)
- Alt-L Toggle Landing Lights
- Alt-M+/- Next Magneto Setting
- Alt-N Toggle Nav Lights (wing red and green lights)
- Alt-P Toggle Pitot Heat
- Alt-S Start Engine
- Alt-T Toggle Taxi Lights
- Alt-X Toggle Master Electric
- Alt-Z Toggle Alternator
-
- F1 VOR1 Decrease OBS
- F2 VOR1 Increase OBS
- Ctl-F1 NAV1 Decrease Freq
- Ctl-F2 NAV1 Increase Freq
- Shift-F1 Toggle NAV1 on/off
- Shift-F2 Toggle NAV2 on/off
- Alt-F1 Swap NAV1 Freqs
- Alt-F2 Swap NAV1 Freqs
-
-
- F3 VOR2 Decrease OBS
- F4 VOR2 Increase OBS
- Ctl-F3 NAV2 Decrease Freq
- Ctl-F4 NAV2 Increase Freq
- Shift-F3 Toggle ADFR1 on/off
- Shift-F4 Toggle ADFR2 on/off
- Alt-F3 Swap NAV2 Freqs
- Alt-F4 Swap NAV2 Freqs
-
-
- F5 ADF1 Decrease Card
- F6 ADF1 Increase Card
- Ctl-F5 ADFR1 Decrease Freq
- Ctl-F6 ADFR1 Increase Freq
- Shift-F5 Toggle COMM1 on/off
- Shift-F6 Toggle MARKERS on/off
- Alt-F5 Swap ADFR1 Freqs
- Alt-F6 Swap ADFR1 Freqs
-
- F7 Retract Flaps
- F8 Extend Flaps
- Ctl-F7 ADFR2 Decrease Freq
- Ctl-F8 ADFR2 Increase Freq
- Shift-F7 Toggle TRANSPONDER on/off
- Alt-F7 Swap ADFR2 Freqs
- Alt-F8 Swap ADFR2 Freqs
-
-
- 3
-
- Home Nose Down Trim
- End Nose Up Trim
-
- Up Nose Down Elevator
- Down Nose Up Elevator
-
- PgUp Increase Throttle
- PgDn Decrease Throttle
-
- Grey + Increase Prop Pitch
- Grey - Decrease Prop Pitch
-
- Numeric 5 Center Ailerons, Elevator, and Rudder
-
- Numeric 0 Left Rudder
- Numeric . Right Rudder
-
- Alt-1 Set Time Compression
- through to number
- Alt-9
-
- ====>>>> Key Commands available in Map Screen <<<<=====
-
-
- Tab Highlight Next Measure Line
-
- Ctl-J Select Closest Flight Path Dot
-
- Enter Center/Redraw Map
-
- Ctl-R Make Closest Runway End to Map Cursor Active Runway
-
- Esc Abort Current Measure Operations
-
- * Add Waypoint at Map Cursor Positon
-
- @ Air Config
-
- # Ground Config
-
- - Decrease Map Cursor Movement Amount
- + Increase Map Cursor Movement Amount
-
- B Enlarge Current Zoom Slightly
-
-
- 4
-
- C Change Aircraft Location (Current, Ground, or Air Config)
-
- D Draw Path of Flight slowly (to review sequentially)
-
- E Erase Path of Flight, Measure Line or Lines.
-
- G Goto Location (Do Not Move Aircraft)
-
- H Home Map Cursor (return to Aircraft Location)
-
- I Toggle Additional Info mode (Frequencies, ILS Arrows, etc.)
-
- L Toggle Labels only
-
- M Measure Line Toggle
-
- N Return to Normal Zooms (After S and B commands)
-
- O Output Map to Epson Printer
-
- P Toggle Profile
-
- R Toggle Radial Line Draw
-
- S Reduce Current Zoom Slightly
-
- Lft/Rght Move Map Cursor
- Up/Down
- Home/End (diagonally)
- PgUp/PgDn
-
- F1-F10 Zoom
-
- Ctl-F1-
- Ctl-F10 Zoom Profile
-
- Ctl-Left
- Ctl-Right Scroll Profile
-
-